Best Way To Study For NACE NACE-CIP1-001 Exam Brilliant NACE-CIP1-001 Exam Questions PDF
Updated Verified Pass NACE-CIP1-001 Exam - Real Questions and Answers
NEW QUESTION # 46
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Measuring ditty, tacky, or soft films
- B. Taking measurements too far from the edge of a surface
- C. Rotating the dial too fast when taking measurements
- D. Failing to determine the base metal reading (BMR)
Answer: A,C,D
NEW QUESTION # 47
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 75 Gauge Readings resulting in 25 Spot Measurements
Answer: C
NEW QUESTION # 48
The Inspector's Log Book is generally:
- A. Shredded by the inspector upon project completion
- B. Shared with all parties upon project completion
- C. Submitted to the client upon project completion
- D. Retained by the inspector upon project completion
Answer: D
NEW QUESTION # 49
Digital hygrometers
- A. are used to measure temperature from a distance.
- B. use a thermocouple in contact with the surface to measure temperature
- C. determine relative humidity, air temperature, and dew point temperature:
- D. consist of a bimetallic sensing element protected from wind gusts.
Answer: C
NEW QUESTION # 50
Passivation can best be described as:
- A. Treating metal with a liquid inhibiter
- B. A coating layer applied to the surface to inhibit corrosion
- C. Complete elimination pf the corrosion process
- D. A protective metallic oxide surface layer that slows corrosion
Answer: D
NEW QUESTION # 51
SSPC SP 1 identifies the use of:
- A. Inorganic solvents
- B. Biodegradable detergents
- C. A wide variety of materials
- D. Organic solvents
Answer: C
NEW QUESTION # 52
Dew point is the temperature at which
- A. the air is saturated.
- B. water freezes.
- C. condensation occurs.
- D. humidity decreases
Answer: C
NEW QUESTION # 53
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Cathode
- C. Reference Cell
- D. Anode
Answer: C
NEW QUESTION # 54
Polymerization is the process of:
- A. All thermoplastic coatings
- B. Monomers joining together
- C. All organic coatings
- D. Monomers telegraphing
Answer: B
NEW QUESTION # 55
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 1 cm (.39 inch)
- B. 2.5 millimeters (.10 inch)
- C. 6.35 cm (2.5 inch)
- D. 2.5 cm (1 inch)
Answer: D
NEW QUESTION # 56
ISO ST 3 is described as:
- A. Very Thorough power tool cleaning
- B. Thorough blast cleaning
- C. Thorough hand tool cleaning
- D. Very Thorough hand or power tool cleaning
Answer: D
NEW QUESTION # 57
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 6 to 7 mils (150 to 175 microns)
- B. 5 to 6 mils (125 to 150 microns)
- C. 8 to 10 mils (200 to 250 microns)
- D. 10 to 12 mils (250 to 300 microns)
Answer: A
NEW QUESTION # 58
To be of value the Inspector's documentation must be:
- A. Submitted before the end of the job
- B. Always handwritten
- C. Always typewritten
- D. Timely, accurate and concise
Answer: D
NEW QUESTION # 59
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which hand tool the Contractor selects
- B. It depends on which power tool the Contractor selects
- C. Yes, because the 'two standards are not equivalent
- D. No, because there is no real difference in the standards
Answer: D
NEW QUESTION # 60
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Call the supervisor
- C. Never change his/her mind
- D. Achieve consensus through negotiation
Answer: B
NEW QUESTION # 61
Upon arrival of coating materials, the inspector should
- A. observe and document the amount of material and batch numbers.
- B. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- C. observe and document time frame and environmental conditions between each coat.
- D. observe aryl document that the applicator WFT at regular intervals during application.
Answer: A
NEW QUESTION # 62
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
Answer: B
NEW QUESTION # 63
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor
- B. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- C. Break the blisters to see what's inside
- D. Document the problem and advise the Contractor and Owner's representative
Answer: D
NEW QUESTION # 64
Daily reports are important because:
Select All That Apply
- A. Inspectors rarely change on a project.
- B. Management uses them to make personnel decisions.
- C. the information impacts future projects.
- D. The information aids communication with supervisors.
Answer: B,C,D
NEW QUESTION # 65
In a non-convertible coating the role of the primary solvent is to:
- A. To promote faster cure
- B. To make the coating flow out better
- C. To control the evaporation rate
- D. To dissolve the resin
Answer: C
NEW QUESTION # 66
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. blotter test for the presence of oil and water.
- B. vial lest.
- C. wet film thickness (WFT) measurement.
- D. dry film thickness (DEI) measurement.
Answer: A
NEW QUESTION # 67
Surface profile describes:
- A. The general condition of the surface required after abrasive blasting
- B. The initial condition of the surface prior to abrasive blasting
- C. The level of surface roughness required after abrasive blasting
- D. The level of surface cleanliness required after abrasive blasting
Answer: C
NEW QUESTION # 68
......
Updated PDF (New 2024) Actual NACE NACE-CIP1-001 Exam Questions: https://passleader.torrentvalid.com/NACE-CIP1-001-valid-braindumps-torrent.html