Oct-2024 Pass NACE NACE-CIP2-001 Exam in First Attempt Easily
Free NACE-CIP2-001 Exam Files Downloaded Instantly 100% Dumps & Practice Exam
NACE-CIP2-001 Exam covers a wide range of topics, including surface preparation, coating materials, coating application, and inspection techniques. NACE-CIP2-001 exam consists of 135 multiple-choice questions and is divided into two parts. Part 1 covers the general knowledge and principles of coating inspection, while Part 2 focuses on specific technical aspects of coating inspection. Candidates are required to score at least 70% on each part of the exam to pass and become certified as a Coating Inspector Level 2.
NEW QUESTION # 12
Corrosion is the reverse process of
- A. flaking.
- B. steel manufacturing.
- C. hot dipping.
- D. galvanic deterioration.
Answer: B
NEW QUESTION # 13
Galvanizing performs best in which of the following exposures:
- A. pH below 4
- B. pH of 13
- C. pH between 5-10
- D. pH above 12
Answer: C
NEW QUESTION # 14
A failure caused by applying a coating too thinly is known as
- A. chalking.
- B. pinholes.
- C. cracking.
- D. failure to cure.
Answer: B
NEW QUESTION # 15
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Gathering
- B. Transmission
- C. Distribution
- D. Midstream
Answer: C
NEW QUESTION # 16
Generally for safety considerations, waterjetting hose connections use
- A. a whip-lock device.
- B. a long wand.
- C. filters.
- D. an oil/water separator.
Answer: A
NEW QUESTION # 17
Cold-applied tape
- A. is typically green or led and looks like "painted" finish.
- B. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- C. have a cross-linked polyethylene backing and a heat-activated adhesive.
- D. are identifiable by its distinct colors, usually light blue, green, Or Grey.
Answer: B
NEW QUESTION # 18
When conducting inspections the Inspector should follow which standards:
- A. The specified standards
- B. NACE and SSPC standards in North America
- C. Australian standards in Australia
- D. ISO standards in Europe and Asia
Answer: A
NEW QUESTION # 19
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Require the Applicator to remove the coating
- B. Advise the Owner and write a Non-Conformance report
- C. Stop the job
- D. Ignore the situation
Answer: A
NEW QUESTION # 20
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Structural integrity
- B. a), b), and c)
- C. Air changes
- D. Lighting
Answer: B
NEW QUESTION # 21
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Redo the pre-cleaning based on the other inspectors results
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Advise the other inspector he is using an incorrect method
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION # 22
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by SP 3
- C. SP 1 followed by SP 2
- D. SP 1 followed by acid etching
Answer: C
NEW QUESTION # 23
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Concrete
- B. Coal Tar Enamel
- C. Liquid epoxies
- D. Heat-shrink sleeves
Answer: C
NEW QUESTION # 24
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Level 1 Inspector
- B. Another NACE Level 2 Inspector
- C. A NACE Protective Coating Specialist
- D. A NACE Level 3 Inspector
Answer: D
NEW QUESTION # 25
The primary purpose of Fireproofing coatings are to provide:
- A. fire extinguishing characteristics
- B. Temporary protection for the structure
- C. Explosion resistance
- D. Preferential fuel for the fire
Answer: B
NEW QUESTION # 26
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Safety Enforcement Costs
- B. Lower Application Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Supervision Costs
Answer: C
NEW QUESTION # 27
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Document the readings at the end of the shift
- B. Advise the coating applicator supervisor of your readings
- C. Check to See if the dehumidification equipment is operating correctly
- D. Call your supervisor
Answer: B
NEW QUESTION # 28
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that the most would understand
- B. Language that only technical experts would understand
- C. Language that another NACE Inspector would understand
- D. Language that only in the project would understand
Answer: A
NEW QUESTION # 29
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. type of dehumidification equipment (refrigerant or desiccant).
- B. manufacturer of the equipment.
- C. time of the year (winter/summer).
- D. coating type.
Answer: D
NEW QUESTION # 30
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Suggest to the Owner that the supervisor should be removed from site
- B. Express a willingness to work with the site team and follow the specification
- C. Defend the previous inspector
- D. Challenge the supervisor's authority
Answer: B
NEW QUESTION # 31
You can use magnifiers to examine all of the following EXCEPT
- A. Blisters
- B. Surface cleanliness
- C. Mill scale
- D. Surface profile
Answer: B
NEW QUESTION # 32
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Give them as much advance notice as possible about upcoming changes
- B. Implement immediate to get them motivated
- C. Make sure they are the center of attention in all site meetings
- D. Challenge their value to the team and try to get them out of their comfort zone
Answer: A
NEW QUESTION # 33
Thermal Spray coatings provide:
- A. Inhibitive protection
- B. Barrier protection
- C. Sacrificial protection
- D. Thermal protection
Answer: C
NEW QUESTION # 34
......
Free Exam Updates NACE-CIP2-001 dumps with test Engine Practice: https://passleader.torrentvalid.com/NACE-CIP2-001-valid-braindumps-torrent.html