Valid NSE6_FWF-6.4 Exam Dumps Ensure you a HIGH SCORE (2024)
Pass NSE6_FWF-6.4 Exam with Latest Questions
NEW QUESTION # 21
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the controller CLI, using the diag wireless-controller wlac -d sta command
- B. On the controller CLI, using the WiFi Client monitor
- C. On the AP CLI, using the cw_diag -d sta command
- D. On the AP CLI, using the cw_diag ksta command
Answer: A
NEW QUESTION # 22
Which statement is correct about security profiles on FortiAP devices?
- A. Security profiles can only be applied via firewall policies on the FortiGate.
- B. Security profiles are only supported on Bridge-mode SSIDs.
- C. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.
- D. Security profiles can only be applied to unencrypted wireless traffic.
Answer: C
Explanation:
Explanation
Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic, such as antivirus, web filtering, application control, and IPS. This feature is called local bridging and it allows the FortiAP to forward traffic to the FortiGate for security inspection before sending it to the destination network. This reduces the bandwidth consumption and latency of tunnel mode SSIDs. References: Secure Wireless LAN Course Description, page 9; [FortiOS 6.4.0 Handbook - Wireless Controller], page 46.
NEW QUESTION # 23
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- B. DARRP measurements can be scheduled to occur at specific times.
- C. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- D. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
Answer: B,C
Explanation:
Explanation
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize
{integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION # 24
Which two statements about background rogue scanning are correct? (Choose two.)
- A. Background rogue scanning requires DARRP to be enabled on the AP instance
- B. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band
- C. A dedicated radio configured for background scanning can support the connection of wireless clients
- D. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
Answer: A,C
NEW QUESTION # 25
Six APs are located in a remotely based branch office and are managed by a centrally hosted FortiGate.
Multiple wireless users frequently connect and roam between the APs in the remote office.
The network they connect to, is secured with WPA2-PSK. As currently configured, the WAN connection between the branch office and the centrally hosted FortiGate is unreliable.
Which configuration would enable the most reliable wireless connectivity for the remote clients?
- A. Configure a bridge mode wireless network and enable the Local authentication configuration option
- B. Install supported FortiAP and configure a bridge mode wireless network
- C. Configure a bridge mode wireless network and enable the Local standalone configuration option
- D. Configure a tunnel mode wireless network and enable split tunneling to the local network
Answer: C
Explanation:
Explanation
Look for "Continued FortiAP operation when WiFi controller connection is down" im the link here:
https://docs.fortinet.com/document/fortiap/7.0.4/fortiwifi-and-fortiap-configuration-guide/442078/how-to-config
NEW QUESTION # 26
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- B. DARRP measurements can be scheduled to occur at specific times.
- C. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- D. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
Answer: B,C
Explanation:
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize {integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION # 27
What type of design model does FortiPlanner use in wireless design project?
- A. Integration model
- B. Analytical model
- C. Architectural model
- D. Predictive model
Answer: D
NEW QUESTION # 28
A tunnel mode SSID is configured on a FortiGate wireless controller.
Which task must be completed before the SSID can be used?
- A. Security Fabric and HTTPS must be enabled on the wireless network interface.
- B. The wireless network interface must be assigned a Layer 3 address.
- C. The wireless network to Internet firewall policy must be configured.
- D. The new network must be manually assigned to a FortiAP profile.
Answer: B
Explanation:
Explanation
The wireless network interface must be assigned a Layer 3 address because it acts as the gateway for the tunnel mode SSID traffic. The FortiGate wireless controller uses this interface to communicate with the FortiAPs and the wireless clients. Without a valid IP address, the tunnel mode SSID cannot function properly.
References: Secure Wireless LAN Course Description, page 5; [FortiOS 6.4.0 Handbook - Wireless Controller], page 24.
NEW QUESTION # 29
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Site survey phase
- B. Hardware selection phase
- C. Project information phase
- D. Installation phase
Answer: A,D
Explanation:
Reference:
https://www.automation.com/en-us/articles/2015-2/wireless-device-network-planning-and-design
NEW QUESTION # 30
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)
- A. When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.
- B. When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- C. When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- D. When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.
Answer: B,C
Explanation:
Explanation
According to the web search results, Auto TX Power control is a feature that allows the AP to automatically adjust its transmission power based on the RF environment. The goal is to minimize interference and optimize coverage cells for roaming. When the AP detects any other wireless signal stronger than -70 dBm, it means that there is a potential source of interference nearby, so it will reduce its transmission power until it reaches the minimum configured TX power limit. This will reduce the interference and improve coexistence with other devices. When the AP detects any interference from a trusted neighboring AP stronger than -70 dBm, it means that there is a high density of APs in the area, so it will also reduce its transmission power until it reaches the minimum configured TX power limit. This will balance the load and avoid overlapping coverage areas.
References: AP Transmit Power and Enable Power Reduction with Auto TX, Transmit Power and Antenna Configuration, Meraki Auto RF: Wi-Fi Channel and Power Management
NEW QUESTION # 31
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- B. For both interfaces in the wtp-profile, configure vap-all to be manual
- C. Disable intra-vap-privacy for the Authors vap-wireless network
- D. Increase the transmission power of the AP radio interfaces
Answer: B,C
NEW QUESTION # 32
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and Io devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Reduce the number of wireless networks being broadcast by the AP
- B. Install another AP in the reception area to improve available bandwidth
- C. Increase the transmission power of the AP radios
- D. Enable frequency handoff on the AP to band steer clients
Answer: D
NEW QUESTION # 33
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA2 Personal and radius MAC filtering
- B. Open, with radius MAC filtering
- C. WPA2 Enterprise
- D. WPA3 Enterprise
Answer: A
NEW QUESTION # 34
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- B. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- C. Indicates channels that cannot be used because of regulatory channel restrictions
- D. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
Answer: A
NEW QUESTION # 35
When configuring a wireless network for dynamic VLAN allocation, which three IETF attributes must be supplied by the radius server? (Choose three.)
- A. 65 Tunnel-Medium-Type
- B. 58 Egress-VLAN-Name
- C. 81 Tunnel-Private-Group-ID
- D. 64 Tunnel-Type
- E. 83 Tunnel-Preference
Answer: A,C,D
Explanation:
Explanation
The RADIUS user attributes used for the VLAN ID assignment are:
IETF 64 (Tunnel Type)-Set this to VLAN.
IETF 65 (Tunnel Medium Type)-Set this to 802
IETF 81 (Tunnel Private Group ID)-Set this to VLAN ID.
NEW QUESTION # 36
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are cut out of the map
- B. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: C
NEW QUESTION # 37
How are wireless clients assigned to a dynamic VLAN configured for hash mode?
- A. Using the current number of wireless clients connected to the SSID and the number of IPs available in the least busy VLAN
- B. Using the current number of wireless clients connected to the SSID and the group the FortiAP is a member of
- C. Using the current number of wireless clients connected to the SSID and the number of clients allocated to each of the VLANs
- D. Using the current number of wireless clients connected to the SSID and the number of VLANs available in the pool
Answer: D
Explanation:
Explanation
VLAN from the VLAN pool based on a hash of the current number of SSID clients and the number of entries in the VLAN pool.
NEW QUESTION # 38
Which administrative access method must be enabled on a FortiGate interface to allow APs to connect and function?
- A. HTTPS
- B. SSH
- C. FortiTelemetry
- D. Security Fabric
Answer: D
NEW QUESTION # 39
......
NSE6_FWF-6.4 Exam Practice Questions prepared by Fortinet Professionals: https://passleader.torrentvalid.com/NSE6_FWF-6.4-valid-braindumps-torrent.html